42 پاسخ به “تبدیل منبع تغذیه کامپیوتر ATX به منبع تغذیه نیمکت آزمایشگاه”

1. hello , i have a new power pc supply and i haven't white wire for -5volt ,how are you doing in that case? thanks …

2. FYI my old ATX PSU had a pink wire! Turns out (after a bit of browsing) to be a sensor wire for the 5v rail, similar to the brown wire for the 3.3v rail. Treat in the same manner.

3. لماذا لا تضع ترجمة يكون أجمل

4. Completely overkill with the build

5. 11.186 seems awfully low for a readout on the -12v output.

6. SIR,,
   PLEZS FOR GIVE ME!!!WE LIVE IN AUS IN TASMANIA,,,ENGLISH))
   ,,IAM SO VERY SORRY,,ME/KIDS CNT READ/WRITE VV GOOD,,WE AL WENT TO SPECIAL SCHOOL,,,I GOT 1 KID NEED SPECIAL HELP,,,I CANT FIND A VERY GOOD VIDEO,, HOW TO MAKE!! TH RIGHT!!! POWER BOX,,,,BY USEIN A COMPUTER ((12!!!!VOLT)) POWER BOX))) 1 KNOB FOR A POWER LINE,,,1 FOR A GROUND LINE,,HAVE 1 KNOB TO TRUN IT TO 3V/5V/12V,,,, USE IT FR ANY THING,,,, WITH FULL CONTROL FROM ((0 VOLT TO 50!!VOLT))TO CHARGE ANY THING LIKE BATTERYSS AND SO ON!!,, USE FULL DISPLAY TO SET IT TO CHARGE ANY THING UP TOO 0 VOLT TO 50 VOLT,,HOPE IAM SAYIN IT RIGHT SIR HAGD1 SIR

7. That's quite short yet detail info on ATX power supply.thanks

8. thanks for your efforts

9. please help, i tried to power on my power supply by connect green with black wires with a load but it doesn't work . i tried this way on other two power supply the same thing happening.

10. grat

11. Wtf is wrong with you, the heatshrink isnt decoration

12. You are the man. This opened my eyes to alternatives to my cnc power supply needs.

13. You should have mentioned to use an air compressor to remove any swarf from drilling the case or Remove the main board before drilling… Your soldering iron tip needs a good clean… 8/10

14. This is the best video on ATX power supply conversion. I’ve watched most of the popular ones and yours is the most thorough and easy to understand. Thanks!

15. There are many of these conversions on youtube but this one is the best one by far.

16. do we need to use bunches of red, yellow etc…for delivering 3.3, 5, 12 V etc, can we use use single wire instead, liked used in case of -12V and -5V

17. Very well done bro

18. Nice video! That's a cool little heat torch, where'd you get it?

19. Where can I get the board schematic?

20. Hi any recommendations for my 650w psu

    It has most of its power on 12v rail 648w at 54amps. All other rails are under 25amps

    What dummy load value should I use

21. Thanks very informative

22. I have a question!! Would I be able to get enough amps out of a power 💪 supply to run 🏃 a car 🚗 stereo and amplifier as well !! Thankyou

23. Nice

24. Never drill metal on top of electronic components or you'll get a bad surprise.

25. Nice video, but I've got a question to ask: is 5W 24ohm dummy load resistor enough for 12v wire?

26. Lastly make sure ac wire don’t touch dc wire !(another false signal

27. Ground ? Wich one ac ground or dc ground ? Ac ground wire size? Does t matter ! Dc ground wire? Need to be bigger then the +12 volt
    So dc ground say need to be 16 gauge , and +12 volt need to be 18 gaige(size is just a reference about the concept ! I didn’t come up with it all vehicule in America do this !

28. Discharging caps is a bonus safety feature 🙂

29. Very neat

30. Help needed, what does he mean by mains wires

31. Very good tutorial.

32. C

33. Today I'll finish this project after at least 4 years since I've seen this tutorial.
    I really hope you will come back making videos because I apreciated your skills very much

34. @Jumperonetv +Jumperonetv is it possible to use a display from a cheap multimeter?

35. ممتاز واصل

36. This is a super video but….can anyone explain why my modern ATX PSU works great powering my external DVD writer (5V 1.5A + 12V 2.0A) simply by shorting the green wire to ground AND without the addition of load resistors?

37. Interesting video but definitively assumes you know A LOT by the way he explain and skip explanation. Not for a newbie.

38. Question, I have a power supply that when I connect the green and black cables . It turns on for a while then goes dead , what am I doing wrong ?? Please help me !!!!
    Thanks

39. Great job brother 👍 Super build

40. i want to ask about the current when you attach 3 wires from the same color like you did with yellow is't not going to assemble the current 14+14+14= 42 Am, is that not a big current for a lab circuit or all the source of yellow part are generate the same current witch mean all the yellow are sharing this 14 Am like in parallel circuit ??
    i hope you can explain to me the current behavior here PLZ !!!

41. Great job Thank you very much 👍

42. modifay atx 14.1 volt

نظرات بسته شده اند.